KINGPRINT DRV8825 Stepper Motor Driver Module with Heat Sink for 3D Printer Rrerap Ramps 1.4 A4988 (Pack of 5pcs)

KINGPRINT DRV8825 Stepper Motor Driver Module with Heat Sink for 3D Printer Rrerap Ramps 1.4 A4988 (Pack of 5pcs)

    Features:

  • -The module has a pinout, it can be used as a better performance of the pull-down menu board replacement in many applications
  • -DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step)
  • -It uses 8.2 – 45 V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling)
  • -Intelligent chopping control automatically selects the correct current decay mode (fast decay or slow decay)
  • -Built-in voltage regulator (the need for any external logic supply voltage)

HiLetgo 5pcs DRV8825 Stepper Motor Driver Module for 3D Printer RepRap 4 RAMPS1.4 StepStick

HiLetgo 5pcs DRV8825 Stepper Motor Driver Module for 3D Printer RepRap 4 RAMPS1.4 StepStick

    Features:

  • DRV8825 Stepper Motor Driver Module
  • 45 V maximum supply voltage
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Can interface directly with 3.3 V and 5 V systems
  • Simple step and direction control interface

ARCELI 5pcs DRV8825 Stepper Motor Driver Module for 3D Printer RepRap 4 RAMPS1.4 StepStick

ARCELI 5pcs DRV8825 Stepper Motor Driver Module for 3D Printer RepRap 4 RAMPS1.4 StepStick

    Features:

  • DRV8825 Stepper Motor Driver Module
  • 45 V maximum supply voltage
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Can interface directly with 3.3 V and 5 V systems
  • Simple step and direction control interface

ALMOCN 6PCS DRV8825 Stepstick Stepper Motor Driver Module with Heat Sink for 3D Printer RepRap RAMPS 1.4,Purple

ALMOCN 6PCS DRV8825 Stepstick Stepper Motor Driver Module with Heat Sink for 3D Printer RepRap RAMPS 1.4,Purple

    Features:

  • A simple steps and direction control interface
  • Maximum 45 V supply voltage
  • Six different steps resolutions: full step, half step, 1/4-step1/8-step1/16-step, 1/32-step
  • Over-temperature thermal shutdown, overcurrent shutdown, undervoltage lockout
  • 4-layer, 2 oz copper PCB for improved heat dissipation

DAOKI 5Pcs DRV8825 3D Stepper Motor Drivers Module for 3D Printer RepRap StepStick for Arduino with Heat Sink Carrier

DAOKI 5Pcs DRV8825 3D Stepper Motor Drivers Module for 3D Printer RepRap StepStick for Arduino with Heat Sink Carrier

    Features:

  • DRV8825 driver board widely used in 3D printers and small CNC machines. The module has a pin out, it can be used as a better performance of the pull-down menu board replacement in many applications.
  • Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
  • It uses 8.2 – 45 V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling).
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates.
  • Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay). Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout.

Witbot DRV8825 Stepper Motor Driver Module 4-Layer with Mini Heat Sink for 3D Printer RP1.4 A4988(Pack of 5pcs)

Witbot DRV8825 Stepper Motor Driver Module 4-Layer with Mini Heat Sink for 3D Printer RP1.4 A4988(Pack of 5pcs)

    Features:

  • 1.It is upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance.
  • 2.The DRV8825 stepper motor driver carrier board TI DRV8825 micro bipolar stepper motor drive is a breakthrough.
  • 3.Stepper Motor Driver (Header Pins Soldered) is a breakout board for DRV8825 microstepping bipolar stepper motor driver.
  • 4.Could be operated from 8.2V to 45V and can deliver up to approximately 1.5A per phase. It comes with 0.1″-pitch male header pins installed
  • 5.Six different stepping resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step,1/32-step

DRV8825 High Current Stepper Motor Driver Carrier

DRV8825 High Current Stepper Motor Driver Carrier

    Features:

  • Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
  • 45 V maximum supply voltage
  • Built-in regulator (no external logic voltage supply needed)
  • Can interface directly with 3.3 V and 5 V systems

SUBALIGU 5pcs DRV8825 Stepper Motor Driver Module with Heat Sink for 3D Printer RepRap 4 RAMPS1.4 StepStick

SUBALIGU 5pcs DRV8825 Stepper Motor Driver Module with Heat Sink for 3D Printer RepRap 4 RAMPS1.4 StepStick

    Features:

  • DRV8825 Stepper Motor Driver Module
  • 45 V maximum supply voltage
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Can interface directly with 3.3 V and 5 V systems
  • Simple step and direction control interface

Aoicrie 5pcs DRV8825 Stepper Motor Driver Module with Heat Sink for 3D Printer Rrerap Ramps 1.4 A4988 StepStick

Aoicrie 5pcs DRV8825 Stepper Motor Driver Module with Heat Sink for 3D Printer Rrerap Ramps 1.4 A4988 StepStick

    Features:

  • This DRV8825 Stepper Motor Driver Module is upgrade of A4988 Simple step and direction control interface ,It is upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates,It uses 8.2 – 45 V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling)
  • Stepper Motor Driver (Header Pins Soldered) is a breakout board for DRV8825 microstepping bipolar stepper motor driver,Intelligent chopping control automatically selects the correct current decay mode (fast decay or slow decay), Built-in voltage regulator (the need for any external logic supply voltage)
  • The module has a pinout, it can be used as a better performance of the pull-down menu board replacement in many applications,Could be operated from 8.2V to 45V and can deliver up to approximately 1.5A per phase. It comes with 0.1″-pitch male header pins installed
  • DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step),Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step

As an Amazon Associate I earn from qualifying purchases.

Random products:

akshay kumar movies
akpi powder